Overclocking Settings Factory

GenesisX · 07-02-2008, 03:59 AM

I'm not quite sure if this thread has been started before; never did come on AnimeA for a good 3-4 months. Anyhow... I guess I'll start...

CPU:E2180
Mobo:P5K-SE (Lower end)
Ram: OCZ XTC Rev ii 2x1 GB (rated @ 800mhz)

Stock @ 2 ghz

Overclock @ 3 ghz (300 FSB with 10x multiplier) (50% overclock)

Timings @ 2T, 4-4-4-12 (sometimes reset 5-5-5-15/18)
All Spectrums, and Boosters off:
Ram Voltages @ 2.15 V
CPU Voltages @ 1.4 V
CPU to Ram Bridge @ 266 mhz
FSB @ 300 Mhz
RAM @ 75x Mhz
Intel Step - up capabilities are off currently.

Idle Temps @ 26 degrees celcius,
On load @ n/a
HSF: Aftermarket

Super PI 32 MB Calculations: Initial Value in 15s., Loop 1: 1s, loop 2: 52s, Loop 3: 42s... Just noticed (done with F@H on).
Not sure if stable; never tested in Orthos or Prime. Sometimes reboots after sometime in moderate CSS gaming. Never reboot in LFS 2 hrs play however.

BlackBlade · 07-02-2008, 04:24 AM

Welcome back mate! I missed your tech talks. ;-)

Thats a nice overclock. I would love to see you post some CPU-Z numbers for us.
http://www.cpuid.com/cpuz.php
You can even post it here to show off to the world:
http://valid.x86-secret.com/

Put it through at torture test and see how well it does! Again, great job. Did you change the CPU or RAM voltages at all?

night_vision · 07-02-2008, 06:00 AM

thanks for posting = D

GenesisX · 07-04-2008, 05:17 AM

Yeah... in fact i did change the voltages. The stock voltage for the proc was somewhere around 1.2-1.28??. Some how I just managed to put 1.43V. It was some mistake I guess. I've seen people go from 2.4ghz to 3 ghz with minimal ups (1.32V) on the Q6600.

(meh, i saw on the internet my ram. it seems that the timings are supposed to be 4-4-4-15, which i set to right after i rebooted!)

Ram, I think stock was at 1.8 or 1.9. Had to be on the safe side, as it wouldn't boot with cpu speeds (FSB) over 320 or so (ram was around 830 or something) Also wouldn't boot if my bridge was set to 333mhz (dunno why)

The settings were kinda improved abit, like how i slowly improve my suspension in GT4 for drifting. Though these ones always screw in the end, and i always end up reverting to the default =S.

1T vs 2T...??

07-02-2008, 03:59 AM	#1 (permalink)
GenesisX Chaos Join Date: Jul 2007 Location: Toronto Age: 15 Posts: 165 Rep Power: 0	Overclocking Settings Factory I'm not quite sure if this thread has been started before; never did come on AnimeA for a good 3-4 months. Anyhow... I guess I'll start... CPU:E2180 Mobo:P5K-SE (Lower end) Ram: OCZ XTC Rev ii 2x1 GB (rated @ 800mhz) Stock @ 2 ghz Overclock @ 3 ghz (300 FSB with 10x multiplier) (50% overclock) Timings @ 2T, 4-4-4-12 (sometimes reset 5-5-5-15/18) All Spectrums, and Boosters off: Ram Voltages @ 2.15 V CPU Voltages @ 1.4 V CPU to Ram Bridge @ 266 mhz FSB @ 300 Mhz RAM @ 75x Mhz Intel Step - up capabilities are off currently. Idle Temps @ 26 degrees celcius, On load @ n/a HSF: Aftermarket Super PI 32 MB Calculations: Initial Value in 15s., Loop 1: 1s, loop 2: 52s, Loop 3: 42s... Just noticed (done with F@H on). Not sure if stable; never tested in Orthos or Prime. Sometimes reboots after sometime in moderate CSS gaming. Never reboot in LFS 2 hrs play however. __________________ "Microsoft: You've got questions. We've got a dancing paperclip." Last edited by GenesisX; 07-02-2008 at 04:01 AM.

07-02-2008, 04:24 AM	#2 (permalink)
BlackBlade Head Tech Guru Join Date: Apr 2007 Posts: 1,849 Rep Power: 679	Welcome back mate! I missed your tech talks. ;-) Thats a nice overclock. I would love to see you post some CPU-Z numbers for us. http://www.cpuid.com/cpuz.php You can even post it here to show off to the world: http://valid.x86-secret.com/ Put it through at torture test and see how well it does! Again, great job. Did you change the CPU or RAM voltages at all? __________________ Sig created by blitzbullet **AnimeA's Official* Tech Guru*** Read my web security review of the latest security programs! http://www.animea.net/forums/f20/bla...-review-16114/

07-02-2008, 06:00 AM	#3 (permalink)
night_vision Salamander! Join Date: Aug 2006 Location: Canada Posts: 1,779 Rep Power: 406	thanks for posting = D __________________

07-04-2008, 05:17 AM	#4 (permalink)
GenesisX Chaos Join Date: Jul 2007 Location: Toronto Age: 15 Posts: 165 Rep Power: 0	Yeah... in fact i did change the voltages. The stock voltage for the proc was somewhere around 1.2-1.28??. Some how I just managed to put 1.43V. It was some mistake I guess. I've seen people go from 2.4ghz to 3 ghz with minimal ups (1.32V) on the Q6600. (meh, i saw on the internet my ram. it seems that the timings are supposed to be 4-4-4-15, which i set to right after i rebooted!) Ram, I think stock was at 1.8 or 1.9. Had to be on the safe side, as it wouldn't boot with cpu speeds (FSB) over 320 or so (ram was around 830 or something) Also wouldn't boot if my bridge was set to 333mhz (dunno why) The settings were kinda improved abit, like how i slowly improve my suspension in GT4 for drifting. Though these ones always screw in the end, and i always end up reverting to the default =S. 1T vs 2T...?? __________________ "Microsoft: You've got questions. We've got a dancing paperclip."

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode